4/29/2023 0 Comments Hp raid monitor linux![]() ![]() This is possible with Windows Server OSes, and then Hard Disk Sentinel would be able to access the status of the members of the RAID. using Windows software RAID arrays to create and manage the RAID array with Windows - instead of the RAID controller which blocks most functions we'd need. If no hard disk status information displayed, then I'd suggest to consider I'm afraid this driver may not install on your chipset. Generally, Intel chipset driver 9.6.5 listed on the above mentioned Driver Zone page was the first, really working driver where the RAID members can be accessed. I'd again suggest to please use Report menu -> Send test report to developer option to check the current situation and advise.ħ) Intel RAID controllers starting from ICH7R chipsets supported without problems. Older / low-end Promise controllers simply did not contain the required functions to access hard disk status (even for standalone hard disks, not only for RAID). Of course if technically would be possible to add support, it will be immediately added to Hard Disk Sentinel.Ħ) The latest versions of Hard Disk Sentinel supports many different Promise RAID controllers, from the higher lines, for example Promise SuperTrak series as described on the compatibility page. (which is displayed on the Information page in Hard Disk Sentinel when you select the appropriate hard disk).Īlso I'd again suggest to please use Report menu -> Send test report to developer option to check the current situation and advise.ĥ) Yes, HP Smart Array controllers is a big problem: even if we contacted HP about this issue long time ago about the situation, we received no positive feedback. Generally, the Support -> Driver Zone section at is designed exactly to offer better, working drivers for hard disk controllers / chipsets, so I'd suggest to check that page and try a recommended driver for the actual controller If it's status is not detected, then it is also caused by the current driver of the controller / motherboard, where the hard disk is connected. It is possible that a driver update is required (if possible) as then the status may be accessed.Ĥ) The item you wrote is a hard disk model, not a RAID controller. ![]() I'd suggest to please use Report menu -> Send test report to developer option as then it is possible to check the actual situation. ![]() This include Adaptec 2xxx series and above, but due to the decision of Adaptec, integrated HostRAID and 1xxx series (low-end Adaptec controllers) can't be supported.ģ) Did you try the latest possible version 4.40 or even the latest possible beta version from. I'm afraid LSI SCSI RAID controllers do not work this way, that's why LSI MegaRAID series listed as not supported on the above mentioned compatibility list, just LSI SATA / SAS series contain the required functions.Ģ) As you can see on the compatibility list, many Adaptec controllers supported and should work. Let's see the actual controllers / situations you described with more details:ġ) From older SCSI RAID controllers, only very few support accessing hard disk information when hard disks configured to RAID arrays, these are some Adaptec SCSI RAID controllers. We're doing our best to analyse other RAID controllers - and if technically it is possible to access hard disk status, I can confirm Hard Disk Sentinel will immediately support detection of further disk details in a future version. That's why only these controllers are listed as supported RAID controllers at. Many RAID controllers (for example 3ware/AMCC, Areca, HighPoint, LSI, Dell, NVIDIA, Intel, Silicon Image, JMicron, Adaptec, etc.) have special methods which allow detection of more information in this situation (so these controllers are already supported). information (including temperature and health) are not displayed, just you can see a "virtual" device instead of the real disk model. Some RAID controllers (usually older / lower quality ones) do not provide access to the hard disks connected and configured into RAID arrays.Īs you can see, the controller may completely hides all physical disk information - that's why the real disk type and S.M.A.R.T. If it would depend on us - then all controllers would be already supported. Thanks for your message and thanks for using registered version of Hard Disk Sentinel software.Įxcuse me for that, however, I can confirm this is not a bug in the software but a limitation of the RAID controller and/or the current driver used for the controller where the hard disk(s) are connected. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |